Drivers ULI Hard Disk Controller

by



This package supports the following driver models: ULi SATA Controller (M5287). Oct 12, 2016 The Bios will recognize the drives, but both Dell diagnostics and a Windows install cd give the error: no hard drive detected, or disk controller not supported. Successful Hard Drive Controller Replacement: In this instructable I walk through the steps that I followed to successfully diagnose and replace the faulty controller board on my old Maxtor 80GB hard drive, and ultimately allowed me to get my data back. Disclaimer: The following instructions.

Ashwani Tiwari | Modified: November 9th, 2020 | Windows Error

“I have a desktop that I added PCI based raid controller card as well. The BIOS displays the card and I was able to configure Raid 1 without any issue. But when I try to install Windows I got an error message “Windows cannot be installed to disk. This system hardware may not support booting to a disk. Ensure the disk controller is enabled in the computer’s BIOS Menu.”

So, could you please help me to fix the issue of how to enable the disk controller in the computer bios menu? Your help would be greatly appreciated.”

Are you still facing the same issue? Not able to understand what to do and how to enable the disk controller in the BIOS menu? Do not worry, you are landed on the right page. In this blog, we will discuss different ways to enable the disk’s controller in BIOS menu.

Drivers

Expert Suggestion:
In case of data loss, try out this utility:

Manual Way to Enable Disk Controller in BIOS

There are multiple ways to enable AHCI mode for SATA on PC where Windows is already installed, and Windows that normally run after this operation. Please have a look on steps to solve your query on how to enable disk controller in bios menu windows 10:

Drivers Uli Hard Disk Controller Of Ssd

  • First of all, run the Registry Editor
  • For this, press Windows + R and type regedit in the command line box
  • Go to this section HKEY_LOCAL_MACHINE SYSTEM CurrentControlSet Services iaStorV
  • Double-click on Start icon and set its value to zero (0)
  • In the upcoming section, HKEY_LOCAL_MACHINE SYSTEM CurrentControlSet Services iaStorAV StartOverride set zero value for element 0
  • In this section, HKEY_LOCAL_MACHINE SYSTEM CurrentControlSet Services storahci set some values to zero for Start element.
  • In the next subsection, HKEY_LOCAL_MACHINE SYSTEM CurrentControlSet Services storahci StartOverride set zero value for element 0.
  • In this case, there is nothing to be seen, but you can see, if AHCI may not be enabled yet.
  • Close the Registry Editor
  • Restart the system and go to BIOS or UEFI. For the first time after a restart, it is always better to boot Windows in safe mode
  • In BIOS or UEFI, find SATA settings to choose the particular mode for memory devices. Switch all of them to AHCI, save settings and restart the PC
  • After restarting, Windows can start the installation of SATA drivers, and when it gets over, it will ask for another restart. To do so, users will enable the AHCI mode in Windows. (If the above method does not work properly, here is another solution. To initiate with, if users have problems with booting Windows in AHCI mode, return to IDE and restart the desktop, After doing this:)
  • Start the Command promptas an Administrator
  • Type “bcdedit /set {current} safeboot minimal” in the command prompt and press Enter key
  • After getting a message that the operation successfully completed, restart the computer system
  • Before booting the system, enable the disk controller in BIOS or UEFI using the above method and save the settings
  • The PC will only boot up in safe mode and install all required drivers.
  • Again, launch Command prompt as Administrator and type in bcdedit /deletevalue {current} safeboot
  • Once the command is executed, restart the PC again. This time, Windows needs to boot with AHCI enabled and without any restrictions.

Well, these instructions can theoretically result in unintended consequences like the inability to start the operating system. Moreover, this method requires technical skills and knowledge to accomplish the task. Here you have got the solution for your query How do I enable disk’s controller in the BIOS menu?

Hard Disk Controller Driver

Data Loss Solution!!

There might be an instance, wherein the drive gets corrupt or format while enabling the disk controller in BIOS. Therefore, to resolve all such issues, one can use Computer Data Recovery Software. It is a simple and reliable solution, which helps to recover all deleted files from the HDD. It is not the solution for your main concern on how to enable disk controller in the computer bios menu Windows 10, 8, 7 and brands Asus, Acer, Sony Vaio, Dell, Samsung etc.

Hard Disk Controller Failure

Time to Conclude

Drivers Uli Hard Disk Controller Manual

At certain times, some users fail to enable disk controller in BIOS. This situation occurs due to several reasons. Therefore, in this blog, we have discussed a manual procedure to enable the disk’s controller in the BIOS menu. Else, users can opt for a reliable third-party tool, listed above. Mainly focused on steps to enable disk controller in bios menu Sony Vaio, Asus, Acer, Dell, Samsung in Windows 10, 8, 7 etc.